Calverton Electrical Company handles electrical work for homes and businesses across Calverton and Montgomery County, Maryland. Calling an electrician doesn't have to be stressful, and from the first call through the final connection, the process is straightforward. You get a clear explanation of the work, a price before anything is scheduled, and no-pressure estimates, priced up front. Flickering lights and warm outlets are warning signs, not quirks. Residential wiring. Commercial wiring. One number for both.
For residential and commercial electrical work alike, the scope of what we handle runs from a single dead outlet to a full service upgrade. Repairs, troubleshooting, new outlets and switches, lighting, ceiling fans, panel work, wiring and rewiring, dedicated circuits, EV charger installation, backup generator hookups, and whole-home surge protection are all part of what gets scheduled through one call.
Most calls start with a symptom: a breaker that keeps tripping, a room that lost power, a switch that stopped responding. We work through the fault systematically, from the panel to the outlet, and explain what we find before any work begins. GFCI and AFCI protection, grounding and bonding, and code-compliant wiring are part of how the job gets done, not extras to negotiate. Electrical work done to the standard the next inspection expects is the baseline, not the exception.
Dealing with a tripping breaker or a dead outlet? These are among the most common calls we get, and they rarely have a single obvious cause without a proper look at the circuit. A breaker that won't reset, an outlet that stopped working, a burning smell near a receptacle, or a section of the house with no power all point to something that needs a diagnostic visit rather than a reset and a wait.
A troubleshooting visit covers the full circuit path: the panel, the wiring run, the device, and the connections at each point. Arc-fault and ground-fault breakers get checked as part of that process where they are involved, because a nuisance trip and a genuine fault can look the same from the switch. We explain what we find and what fixing it involves before any work is authorized. Reach out and we'll get it diagnosed.
Montgomery County carries a wide range of housing ages, and Calverton is no different. Homes built in the 1960s through the 1980s often have panels sized for the electrical loads of that era, not the loads a modern household puts on a circuit. Knob-and-tube wiring, aluminum branch-circuit wiring, and fuse boxes that have been patched rather than replaced are not unusual in properties of that age.
That matters because the work changes depending on what is already there. A panel upgrade in a home with original wiring is a different job from one in a house that was rewired ten years ago. An outlet added to a circuit with aluminum wiring needs the right connectors and devices, not just a standard receptacle. Knowing what the housing stock in this area commonly holds means fewer surprises once the panel is open and the walls are checked.
Older panels in Montgomery County homes were often installed at 100 amps, which was adequate for the appliance loads of the time. A household running a modern kitchen, EV charger, and home office on that same service can run into capacity problems that show up as tripping breakers, slow chargers, or circuits that can't support the load reliably.
A service upgrade from 100 to 200 amps involves replacing the panel, the service entrance conductors, and coordinating the meter work with the utility. Subpanel installation, load calculations, and breaker replacement are all part of what gets handled on the electrical side. Panel and wiring work finished to code is what the job produces, and the scope is confirmed before anyone starts. We'll find the fault and fix it right.
Whole-home rewiring is one of the larger jobs we handle, and it is often the right answer for properties where the existing wiring has reached the end of its useful life. Knob-and-tube replacement involves running new circuits through finished walls, updating the panel, and installing modern outlets and devices throughout. Aluminum-wiring remediation addresses the connection points where aluminum meets devices rated for copper, either through proper connectors or by replacing the affected runs.
An electrical safety inspection is often the starting point for these projects. It gives a clear picture of what is present, what meets current standards, and what needs attention before a sale, a renovation, or a new appliance load is added. Surge protection and dedicated circuits frequently accompany a rewiring project, since the panel is already open and the circuits are being planned fresh. We make the fix and leave it tidy.
Recessed lighting, under-cabinet lighting, outdoor and security lighting, motion sensor fixtures, ceiling fans, new outlets, and dimmer switches are the installs that make up a large share of the calls we handle week to week. Each one involves more than swapping a device: the circuit has to support the load, the box has to be rated for what is being mounted, and the wiring has to be connected correctly at both ends.
Exterior lighting matters for Calverton properties where the driveway, walkway, or rear yard needs coverage after dark. Landscape lighting circuits, security floodlights, and motion-activated fixtures are all jobs that get run from the panel and terminated at weatherproof boxes outside. Indoor installs like recessed LED lighting and ceiling fan replacements follow the same process: confirm the circuit, check the box, make the connections, test the result. Dead outlets usually have a simple cause worth finding.
Seeing flickering lights or a warm outlet? Both can be symptoms of a circuit carrying more than it was designed to handle. A dedicated circuit separates a high-draw appliance from the shared wiring it may be competing with, whether that is a refrigerator, a washer and dryer, or a sump pump in a finished basement.
EV charger installation at the Level 2 standard involves running a dedicated 240-volt circuit from the panel to the garage or driveway location, sizing the breaker correctly for the charger, and confirming the panel has the capacity before any wire is pulled. Backup generator hookups involve the transfer switch, the inlet connection, and the circuit that feeds the loads the generator will cover. Whole-home surge protection gets installed at the panel and protects the circuits that run through it. Every one of these jobs is scoped at the panel first, and the price is confirmed before scheduling.
Commercial properties in Calverton and across Montgomery County have electrical needs that differ from residential work in scale and in the code requirements that apply. Office spaces, retail units, and light industrial properties all need circuits sized for their actual loads, panels that can support future changes, and wiring that meets the standards a commercial inspection will check.
We handle commercial panel upgrades, circuit installation, outlet and lighting work in occupied spaces, and code-correction wiring for properties that need to come into compliance. The scope of a commercial job gets confirmed on the call the same way a residential one does. Electrical work done to the standard the next inspection expects applies just as much in a commercial suite as it does in a single-family home.
The scope and the price are settled on the call before anything is booked. When you describe the problem or the project, the person you are speaking with knows the trade and can work through what the job involves, what it is likely to require at the panel and circuit level, and what the visit will cover. That conversation produces a price, not a vague range to be confirmed on arrival.
The same number that books the job is the number to call with questions afterward. There is no separate billing line, no account portal, and nothing to track down later. What the job covers is agreed before anyone starts, and that agreement does not change once the work is underway.
We are available every day from 7:30 AM to 8:00 PM, which covers most of the scheduling windows that homeowners and property managers need, including evenings and weekends. Electrical faults do not follow a Monday-to-Friday schedule, and neither does ours. If a breaker is tripping repeatedly or an outlet has stopped working entirely, those calls get answered within those hours and handled as the priority they are.
Getting a quote means calling, describing the job, and getting a price on that call. The price covers what was discussed, and if the scope changes once the panel is open, that gets communicated before the additional work proceeds. There are no promises made here about what the final invoice will not contain, because the job is scoped on the call, not on this page. What you can count on is a straight answer when you ask what it covers.
We work throughout Calverton and the wider Montgomery County area, including Burtonsville, Spencerville, Colesville, Silver Spring, Gaithersburg, and Rockville. Residential and commercial calls from across the county are handled through the same number, and the geographic range covers both the closer neighborhoods and the communities further out in the county.
If your address is nearby and not on this list, call and ask. The service area covers more ground than any short list can name.
Older homes in this part of Maryland commonly carry knob-and-tube wiring, aluminum branch circuits, or panels that were sized for a lighter load than a modern household puts on them. We see these systems regularly and know what to look for when the panel is open or the walls are checked. That familiarity shapes how we scope the job and what we recommend before any work starts.
The work is scoped on the call, confirmed before anyone starts, and completed to the standard the next inspection expects. Connections are made correctly, devices are rated for the circuit, and the panel is left in the condition it should be in. Before we leave, the circuit is tested and the work is explained so you know what was done and why.
If we find something during the work that changes the scope, we stop and explain it before continuing. Nothing additional is done without your agreement, and the price for any added work is confirmed on site before it proceeds. We show up, and we keep you posted until the job is done.
The more specific you can be, the faster the diagnostic goes. Note which outlets or switches are affected, whether the problem is constant or intermittent, whether a breaker has tripped, and whether there is any smell, sound, or warmth near the device or panel. That information lets us scope the visit accurately on the call.
The work is carried out locally by someone who knows the trade and the electrical standards that apply in Maryland. The person who answers your call can scope the job and confirm what the visit involves. The electrician who arrives follows the scope that was agreed on the call.
Once the work is complete, the circuit is tested under normal operating conditions. Outlets are checked for correct wiring, breakers are confirmed to trip at the right load, and any GFCI or AFCI devices are tested for proper function. If something does not pass the check, it gets addressed before we leave.
A clear description of the problem on the call, access to the panel, and a straightforward scope all help. Jobs that run into delays usually involve a scope that changed once the wall or panel was opened, and we handle that by stopping to explain what we found before continuing. Agreeing on the scope and the price before anyone starts is what keeps the job on track.
Calverton Electrical Company is available every day from 7:30 AM to 8:00 PM.
Call (227) 294-9289 to get a quote, ask about availability, or schedule a visit. Simple booking. Clear pricing. Safe, solid wiring.
(227) 294-9289